DAYLIGHTING DRIVEN DESIGN - International Building Performance ...

72 downloads 90237 Views 5MB Size Report
Annual Sun Exposure (ASE) metrics, which forms together a clear ... luminance levels, therefore, ASE is used to describe ..... Engineering School ,Electrical and.
Fifth German-Austrian IBPSA Conference RWTH Aachen University

DAYLIGHTING DRIVEN DESIGN: OPTIMIZING KALEIDOCYCLE FACADE FOR HOT ARID CLIMATE Y. Elghazi1, A. Wagdy2, S. Mohamed3 and A. Hassan4 1 Cairo University, Cairo, Egypt 2 The American University in Cairo, Cairo, Egypt 3 Al Azhar University, Cairo, Egypt 4 Future University in Egypt, Cairo, Egypt

ABSTRACT Facade design has significant impact on daylight. This paper presents a facade based on origami: kaleidocycle rings that can be morphed enhancing daylight performance in residential spaces, which complies with both LEED V4 and Daylight availability. Daylighting analysis was integrated using Grasshopper, Diva and Genetic optimization for a south-oriented living room facade in Cairo, Egypt, through two phases. First phase dealt with base cases of specific typology. Second phase was conducted using parametric optimization process. Results demonstrate that Kaleidocycle rings of 30 cm size and 64 rotation’s angle reached results that exceed LEED v4 requirements while passing Daylight availability standards.

INTRODUCTION As the world gives increased focus on energy efficiency and occupant comfort, there is now an emerging need to include sustahnability–related performance aspects within design, most notably energy and daylighting (Lagios et al., 2010). Façade openings play an important role in providing daylight, which is considered the best source of light that matches human visual response and required colour. Thus, they have a substantial positive impact on the occupants (Li & Tsang, 2008). More recently, New methodologies have been developed to use daylight simulation as a driven tool for design, which showed the benefits of parametric driven façade to reach maximum daylight quality. In this research; daylighting will be the key performance criteria to design non-simplified double façades using parametric design and optmization tools for residential spaces.The paper presents initial findings of an ongoing research.

reduced artificial lighting consumption (Reinhart, 2001). Significant energy savings can be gained if the design process encompasses thoughtful daylighting strategies incorporated into the design process on the early design phases (Jason & El Sheikh, 2011). Daylight Autonomy Daylighting design is a key aspect of building rating systems such as Leadership in Energy and Environmental Design system (LEED). It uses metrics such as Daylight autonomy (DA), which is the percentage of annual work hours during which all or part of a building’s lighting needs can be met through daylighting alone (Reinhart et al., 2006). Two metrics in LEED v4 are codified for evaluating daylight autonomy design, which allow a daylit space to be evaluated for a one year period using two different performance parameters: sufficiency of daylight Illuminance and the potential risk of excessive sunlight penetration (IES, 2012). These two metrics are: Spatial Daylight Autonomy (sDA) and Annual Sun Exposure (ASE) metrics, which forms together a clear picture of daylight performance that can help architects to make good design decisions. sDA describes how much of a space receives sufficient daylight, which is for residential spaces must achieve (sDA 300 lux / 50% of the annual occupied hours) for at least 55% of the floor area as shown in Table 1. sDA has no upper limit on luminance levels, therefore, ASE is used to describe how much of space receives too much direct sunlight, which can cause visual discomfort (glare) or increase the cooling loads. In LEED v4 ASE measures the percentage of floor area that receives at least 1000 lux for at least 250 occupied hours per year (C.Sterner, 2014), which must not exceed 10% of floor area (USGBC, 2013).

Daylighting in residential spaces Daylight is an important element for residential spaces that can contribute to maintain the minimum illuminance level required to improve indoor environmental quality and user comfort. The benefits of a carefully planned daylighting concept range from an enhanced lighting quality for the inhabitants to a

- 314 -

Table 1: LEED v4 - Points for daylit floor area: Spatial daylight autonomy sDA (for regularly occupied floor area)

Points

55%

2

75%

3

Fifth German-Austrian IBPSA Conference RWTH Aachen University

Hybrid Double Façade Egypt’s climate is classified as hot desert arid climate according to Köppen’s climate classification system (Peel et al., 2007). It is characterized by high direct solar radiation and clear sky which demands special façade treatments to minimize heat gain while providing appropriate daylighting. Double-skin façades are one of the building’s envelope solutions that can improve indoor climate while reducing the use of energy if designed properly (Poirazis, 2006). Traditional double façade types of buffer, twin face and extract-air, where the exterior layer is glazed, have been evolved for hot arid climate resulted in a hybrid approach which employs a shading screen as the exterior face coupled with a high performance curtain wall system as the interior layer of the façade (Boake, 2014). Energy savings are dependent on the specific configuration of the exterior shading screen. Screen patterns, tessellated layers, cellular units or origami crease patterns may present efficient solution to minimize heat gain while providing appropriate daylighting.

Figure 2: Al Bahar Towers in Abu Dhabi by Aedas, The folding shading system, opens and closes according to sun's position. Gao & Ramani presented initial prototypical explorations for 3d folding as well as the associated transformative design concept called Kaleidogami. This method is used for developing spatial objects that can be flattened, folded and reconfigured. They developed the concept for a tetrahedral basic structural unit to enable new forms of 3D folding. By rearranging, combining and reconfiguring, one can obtain different configurations with tetrahedral basic structural unit or shape variation of folding representation, encompassing multi-primitive and reconfigurable foldable units (Figure 3).

Origami-Based Design Recently building skin explorations are carried out using inspired new ideas of the ancient art of origami. Origami offers a finite set of paper-folding techniques that can be cataloged and tested with parametric modeling software. Origami is based on the sequence, shape and relationship between surface and points which can be defined by rules (Figure 1). It can be viewed as a type of manual algorithm that can be translated to parametric models (Gao & Ramani).

Figure 1: Origami forms based on geometrical rules and folding morphology. Many origami planar explorations of the triangulatedbased skins have been tested rather than volumetric 3d folding explorations. Lee & Leounis (2011) presented a surface manipulation tool that can transform the arrangement of folding planar surfaces, while Crawford (2010) studied a family of folding geometry to provide ventilation using parametric modeling. On the practical platform, the 25-story twin office towers in the United Arab Emirates feature a computermonitored and sensor-controlled screen as shown in Figure 2, which responds dynamically to the sun, folding like origami to shade or expose the building.

Figure 3: Tetrahedral basic structural unit exploration (Gao & Ramani). Kaleidocycle Skin: Concept and Approach Rotating rings of tetrahedrons called kaleidocyles are well known from recreational mathematics. Each tetrahedron in the cycle is linked to its predecessor and successor at opposite edges. The mobility criterion treats each tetrahedron as a rigid object (Fowler & Guest, 2005). There is a Lot of different kinds of kaleidocycles but the most rigid, stable yet interesting is the Hexagonal Kaleidocycle. Moloney experiments with pattern showed that increasing the number of edges beyond six proved counterproductive, as edge differentiation became harder. Moreover, the hexagon provided a relatively neutral orientation when a large number were combined in an offset (Moloney, 2011). A closed Hexagonal kaleidocycle is tested which is made up of six irregular tetrahedrons with three symmetrydistinct configurations (Fowler & Guest, 2005). These must be made so that: the hinge edges are orthogonal, and bases of isosceles triangles whose altitudes to the vertex angles are the same length as their bases. The kaleidocycle skin is a mix of triangular and hexagon shapes that provide good edge detection and reasonable shading detection. The primary concept of the proposed skin, shown in Figure 4, is that when it rotates, the hole at the center periodically disappears (it closes up) to control different levels of daylight

- 315 -

Fifth German-Austrian IBPSA Conference RWTH Aachen University

penetration using parametric modelling tool. The kaleidocycles are scripted to act as apertures, with a variable hole opening diameter, which will be optimized to improve daylighting performance.

simulation softwares. The Geco plug-in allows the digital model to be analyzed by Autodesk's Ecotect program (Frick & Grabner, 2011). Similarly, DIVA , which stands for Design Iterate Validate Adapt, for Rhinoceros 3D tools, and provides Grasshopper components to perform daylight analysis on an existing architectural model via integration with Radiance and DAYSIM (Reinhart et al., 2011). Parametric simulations can give an idea of the variation in daylighting performance related to the variation of one or more parameters (Torres et al., 2007). Genetic optimization algorithms

Figure 4: Shows the Kaleidocycle rotation motions. Parametric modelling potentials Parametric tools in architecture have been gaining momentum over the past few years. The term refers to digitally modeling a series of design variants whose relationships to each other are defined through mathematical operations and different parameters. These relationships form a parametric space that could generate numerous of related but distinct forms (Schumacher, 2009). This new design approach provides architects with the possibility of making modifications on any parameters without the need to recreate the entire model (Wagdy, 2013), and offering a great potential for geometric design explorations. Using this approach provides architects with a high ability to optimize buildings with respect to various performance aspects. The impact of such a trend is yet to be seen on building forms and envelopes and their behavior with respect to different climate. Grasshopper In recent years, the design professions have begun experimenting with parametric design tools such as Grasshopper which was developed by David Rutten at Robert McNeel& Associates in 2007 as a parametric modelling plug-in for Rhinoceros 3D modeling software (McNeel, 2010). Grasshopper is a graphical algorithm editor that allows designers with no formal scripting experience to quickly generate parametric forms from the simple to the awe-inspiring (Day, 2009) as there are components within Grasshopper that allow custom scripts to be written in VB.NET or C# (Lagios et al., 2010). Daylight simulation tools Since green building rating systems such as the US Green Building Council’s (USGBC) LEED system encourage the use of simulations, designers are increasingly reporting that they are using daylight simulations within their designs (Gasiu & Reinhart, 2008).

Optimization in building design is an interesting point of study because of the integrated nature of both environmental and energy performance.It is used to extensively search the design alternatives looking for high performance solutions in terms of specified goals. The simulation-based optimization can overcome the drawbacks of evaluative trial and error approach. In order to combine parametric modeling with an optimization technique to support design explorations and form finding, Genetic algorithms (GAs) have been considered. GAs can perform a series of simulations in a multi-dimensional search space, increasing the relevance of the cases simulated. They are used to find the configuration that best matches desired performance goals (Monks, Oh, & Dorsey, 2000; Turrin, Buelow, & Stouffs, 2011; Rakha & Nassar, 2011 ). Genetic algorithms were shown to be effective in presenting new solutions to optimize light penetration and shading, taking into account many different aspects that influencing the performance of a façade (Zemella et al., 2011). The prediction of daylight levels by model-fitting was addressed by Coley and Crabb (Coley D, 1997) using genetic algorithms. Park et al. also (Park et al., 2003) maximised daylighting from a double-skin facade using non-linear programming. The principle was then developed into a real-time optimization program using genetic algorithms (Yoon et al., 2011). The above literature review demonstrates that previous research did not present any case study which adopts the new LEED V4 daylighting simulation methodology, especially in hot climate conditions. Limited publications were concerned with the exploitation of window size and shading devisces that control the solar penetration, and thus improvement of daylighting performance while diminishing the direct sunlight expusure could pave the way for their deploying better sustinable designs which can be appropriate LEEDV4 evaluation process.

There have been various plug-ins developed for Grasshopper that connect the Rhino geometry to

- 316 -

Fifth German-Austrian IBPSA Conference RWTH Aachen University

OBJECTIVES The main goal of this research was the enhancement of the daylighting of living room by employ a nonsimpleficed shading techique formed by kaleidocycle rings. In order to achive this goal, an objective was defiend to identify ideal size/rotation of kaleidocycle rings by fullfilling both LEED V4 daylighting requirements and the Daylight Availability dynamic metric. Investigations focused on the use of parametric optimization approach to determine the “nearoptimum” kaleidocycle configuration that suit living room space located in hot arid climate of cairo, Egypt.

Figure 5: Standard South-facing living room with kaleidocycle skin modelled for daylight analysis.

METHODOLOGY

Table 2: Parameters of the used living room.

 

The methodology implemented in this paper was divided into two successive stages. First stage focused on the analysis of daylighting performance for base cases with specific typology, while second phase is conducted using parametric optimization for different facade parameters to achieve the near optimum daylighting adequacy. The two phases used Diva -forRhino (a plug-in for Rhinoceros modelling software). DIVA uses RADIANCE and DAYSIM as its basic daylight simulation engines. Radiance and DAYSIM employ a reverse ray-tracing algorithm based on the physical behavior of light in a volumetric, threedimensional model which should most accurately represent reality (Ward, 1994). RADIANCE/DAYSIM has been validated in many studies (Reinhart & Walkenhorst, 2001; Reinhart & Breton, 2009; Reinhart & Wienold, 2011). They represent accurately occupant comfort, behavior and the distribution of natural light in a space especially when compared to EnergyPlus (Ramos & Ghisi, 2010). In this research, a sidelit space has been defined and constructed a base model on a hypothetical indoor residential space (living room) of 20 m2 at the first floor, facing the south direction , which is located in Cairo, Egypt. Kaliedocycle rings will be applied to this south-oriented façade. It should be noted that the reliability of the simulation results is dependent on a number of factors; the most notable of these is the modelling of the living room details and complex Kaleidocycle skin systems, as well as the geometrical and photometrical properties used. In order to improve the reliability of results, the suggested Kaleidocycle skin was modelled in full detail Figure 5. The properties of the living room, Kaleidocycle skin and the window were fully described in Table 2. Radiance renderings and visualizations of the tested solar screens were examined before simulation runs in order to ensure that the model geometry was correctly exported to the Radiance software.

Indoor Space Parameters Internal Surfaces Materials Walls

Reflectance= 50%

Ceiling

Reflectance= 80%

Floor

Reflectance= 20%

Kaleidocycle Reflectance= Metal diffuse Window Parameters Glazing

VT= 80%

Kaleidocycle Facade logic Rhinoceros and Grasshopper have been chosen as a software platform to generate a parametric folding model focusing on solids’ motion, particularly, by which kaleidocycle transform from one configuration to another. The parametric model served as a mean for better understanding of the geometry of the rings. Each Kaleidocycle ring motion is defined off the original geometry through a series of commands: rotate, move and mirror. Analyses of the movement of each ring in the system led to a discovery; it is possible to maintain the movement of the system by rotating along their axis of symmetry in order to open and close the skin. This allowed us to apply a closed cycle path of movement from end to end. The parametric model starts with a hexagon, where each side of the hexagon represents the axis of symmetry for each tetrahedron. While simulating the movement of each ring the tetrahedrons must be kept connected edge-to-edge. The edges that are forming the tetrahedrons were generated from the vertex of the hexagon to be perpendicular / parallel to the hexagon plane. Each tetrahedron is drawn as surfaces joining the two opposite edges, rotating these edges from its mid points along an axe joining the midpoint with the center of the hexagon, while in the same time moving it towards or away from the center of the hexagon. The concept of the proposed skin depends on the space created between the tetrahedrons as they rotate to open and close the Kaleidocycle rings. Different combinations of Kaleidocycle sizes and angle of

- 317 -

Fifth German-Austrian IBPSA Conference RWTH Aachen University

rotations led to different daylight performance. Those two variables are considered the main parameters of the design which were controlled with numeric sliders. Figure 6 shows various Kaleidocycle size configurations ranging from 20cm to 65cm for each unit with a step size of 5 cm, while Kaleidocycles with different rotation angels ranging from 0 to 90 degrees wit a step size of 10 degrees are illustrated in Figure 7.

Figure 6: shows the Kaleidocycle size configuration ranging from 20cm to 65cm (step size= 5 cm).

Wienold, 2011). This section is focusing on the recreation methodology that was used on this research. Spatial Daylight Autonomy (sDA) The simulation parameters was set to measure daylight Illuminance sufficiency for the living room, DIVA parameters were set to calculate the percentage of analysis points that exceeds a specified Illuminance level (300 lux) for at least 50% of the total occupied hours from 8am-6pm over the year (IES, 2012), while the percentage of sDA should be at least 55% or 75% to achieve 2 to 3 LEED points. However, the authors used an optimization approach to maximize the percentage of sDA more than 75%. For sDA and Daylight availability metric Radiance parameters were set as shown in Table 3. Table 3: The Radiance parameters set for sDA and Daylight Availability metric. Ambient bounces 6

Ambient Divisions 1000

Direct threshold 0

Annual Sunlight Exposure (ASE)

Figure 7 shows the Kaleidocycle rotation angels ranging from 0 to 90 degrees (step size= 10 degrees). Simulation logic The simulation process that was conducted on this research can be considered as one of first application of LEED v4 daylighting methodology; the available graphical interface tools such as DIVA or Ladybug do not provide a straightforward procedure which can be used to evaluate the second criterion of Annual Sunlight Exposure (ASE), therefore the methodology which is presented in this research is original and follows precisely the Approved Method IES Spatial Daylight Autonomy (sDA) and Annual Sunlight Exposure (ASE) descripted in Illuminating Engineering Society report number LM-83-12. The simulation process conducted in this paper complied with both LEED V4 daylighting requirements and Daylight availability (DA). LEEDv4 concentrates on (sDA) and (ASE) which were described before in the literature review. Three Daylight Availability evaluation levels were used: “daylit”, “partially daylit” and “over lit” areas. The “daylit” areas are those that received sufficient daylight at least half of the year-round occupied time. The “partially daylit” areas are those that did not receive sufficient daylight at least half of the yearround occupied time. The “over lit” areas are those areas that received an oversupply of daylight, where 10 times the target Illuminance was reached for at least 5% of the year-round occupied time (Reinhart &

Annual Sunlight Exposure (ASE) is the second metric used by LEED, which searches for any potential source of visual discomfort, particularly the presence of direct sunlight. This metric calculates the percentage of the analysis points that exceeds a specified illuminance level, 1000 lux, for at least 250 hours of the occupied hours without any contribution from the sky (IES, 2012). Grasshopper was used to collect and filter the Illuminance values of each analysis point over 3650 hours, and present the final ASE percentage along with the total number of hours for each analysis points which is exposed to direct sunlight. Grasshopper facilitates the process for all analysis points in order to make it feasible for optimization. Table 4 shows the Radiance parameters that were used to calculate the ASE. Table 4: The Radiance parameters set for the ASE. Ambient Bounces 0

Ambient Divisions 1000

Direct threshold 0

PHASE ONE: BASE CASE SIMULATION First simulation phase dealt with base cases for Kaleidocycle rings of 20 cm size but with different rotation angles ranging from 30 to 90 degrees with a step of 15 degrees as a part of Daylight Availability (DA) simulation as shown in Figure 8.

- 318 -

Fifth German-Austrian IBPSA Conference RWTH Aachen University

100% 80% 60% 40% 20% 0% 30

o

45

Partially lit

o

60

o

Day lit

75

o

90

Illuminance levels did not exceed 3000 lux at any point except the same three points which were declared by ASE metric. A comparison evaluation was made to verify the reliability of the optimization results, the comparison results are illustrated in Table 5. All configurations was tested at 70% WWR which represent the same ratio of the optimized solution.

o

Over lit

Figure 8 : Shows the Daylight Availability (DA) Performance of the Base case The results showed good potentials for the Kaleidocycle rings in enhancing daylighting performance that could be optimized to comply with LEED V4 daylighting requirements as well as Daylight availability (DA) standards.

PHASE TWO: PARAMETRIC OPTIMIZATION This stage aims to optimize the Kaleidocycle configurations by conducting a parametric optimization process. Optimization Parameters All model parameters were fixed except two variables which are used for the optimization as show in Table 5. Table 5: The Optimization Parameters. Optimization Parameters Opening Size 20 cm to 65cm (step 1cm) Rotation Angle

0⁰ to 90⁰ (step 1⁰)

Optimization results The optimization stopped after 73 generations, the best results of each generation is presented in the graphs Figure 9, while each generation contained 30 trials. The graphs show that the daylighting performance results are gradually enhanced till the optimized ones. The optimization objective was set to maximize the daylit area and to minimize the over lit and ASE areas. The last generation of the optimization process reached the optimum solution which eventually gives a better performance than the one required by LEED v4. The optimum solution in shows the Kaleidocycle size became small to have Figure 10 more openings with large angle which allows for better daylighting distribution. On other hand, the daylighting performance of this solution can easily get 3 LEED points because sDA = 100% which is more than the required 75%, and the ASE is equal to 5% which is less two times than the required (10%). Furthermore the daylight availability metric shows a comparable performance, even with 6 bounces the

Table 5: Shows the Daylight Availability (DA) Performance of the comparing cases. Day lit Case Partially Lit Over lit A 0 55 45 B 0 60 40 C 50 30 20 D 0 75 25 E 0 90 5 A:Simple window without shading. B:Simple window with electrochromic 60% VT. C:Simple window with electrochromic 30% VT. D:Double Façade with Kaleidocycle rings, Size =20 cm, Angle=75 degrees. E:Optimized Double Façade with Kaleidocycle rings, Size =30 cm, Angle=64 degrees.

CONCLUSION This paper presents a hybrid double façade design driven by daylight performance through incorporating daylighting simulation tools and genetic optimization with a parametric facade model of an origami-based; kaleidocycle rings. The simulations were conducted for a south oriented façade of a standard living room for hot arid climate of Cairo, Egypt. Several Kaleidocycle parameters were modelled but all of them were fixed except two variables; opening sizes and rotation angles which were used for the optimization process. A two stage methodology was adopted, while the first phase showed potentials in enhancing daylighting performance by changing façade typology, the second phase proved that Kaleidocycle rings of 30 cm size and 64 rotation’s angle reached better daylighting distribution that exceed LEED v4 requirements and passing Daylight Availability standards (Figure 10). The paper demonstrate that integrating daylighting simulation tools and genetic algorithm to drive parametric façade typology contribute in reaching better daylighting performance. In the future, this study will be extended to consider thermal loads in façade design.

- 319 -

Fifth German-Austrian IBPSA Conference RWTH Aachen University

Optimum Soultions LEED v4 Accepted

Daylight Autonomy 100% 80%

60% 40% 20% 0% 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

DA

Annual Sunlight Exposure 100% 80% 60% 40%

20% 0% 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

ASE

Daylight Availability 100% 80%

60% 40% 20% 0% 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73

Partially-Daylit

Daylit

Overlit

Figure 9: Shows DA, ASE and Daylight Availability performance through each generation of the optimization Daylighting Performance

Rotation Angle = 64 Degree

Daylight Autonomy = 100%

ASE = 5%

Opening Size = 30 cm

Partially – daylit = 0% Daylit = 95% Overlit = 5%

Figure

BIBLIOGRAPHY Boake, T. M. (2014). Hot climate Double Facades: Avoiding Solar Gain. 14. C.Sterner. (2014). Measuring Daylight: Dynamic Daylighting Metrics & What They Mean for Designers. Coley D, C. J. (1997). An artificial intelligence approach to the prediction of natural lighting levels. Building and Environment. Crawford, S. (2010). A Breathing Building Skin. Proceedings of the 30th annual conference of the Association of Computer Aided Design in Architecture ACADIA , (pp. 211– 217). Day, M. (2009, June 01). Rhino Grasshopper. Retrieved June 30, 2014, from AEC Magazine: http://aecmag.com/softwaremainmenu-32/293-rhino-grasshopper Etman, O., Tolba, O., & Ezzeldin, S. (2013). DoubleSkin Façades in Egypt between Parametric and Climatic Approaches. Performative and Interactive Architecture - Volume 1 -

Computation and Performance -, (pp. 459466). Fowler, p., & Guest, s. (2005). A symmetry analysis of mechanisms in rotating rngs of tetrahedra. Trumpington Street,Cambridge , United Kingdom: Department of Engineering,University of Cambiradge . Frick, U., & Grabner, T. (2011, November 23). A Collection of Past & Ongoing Works. Retrieved June 15, 2014, from uto: http://utos.blogspot.com/ Gao, W., & Ramani, K. (n.d.). Kaleidogami™: Multi-Primitive Reconfigurable Artistic Structures. School of Mechanical Engineering School ,Electrical and Computer Engineering,Purdue University: by Courtesy. Gasiu, A., & Reinhart, C. F. (2008). Current Daylighting Design Practice: A Survey. 36(2). IES. (2012). Spatial daylight autonomy (sDA) and annual sunlight exposure (ASE). New York (NY): IES. LM-83-12.Lighting Measurement #83.

- 320 -

Fifth German-Austrian IBPSA Conference RWTH Aachen University

Jason, D., & El Sheikh, M. (2011). Building Skin Intelligence- a parametric and algorithmic tool for daylighting performance design integration. ACADIA. Lagios, K., Niemasz, J., & Reinhart, C. F. (2010). Animated Building Performance Simulation (ABPS)-Linking Rhinoceros/Grasshopper With Radiance/Daysim. SimBuild. New York City. Lee, D., & Leounis, B. (2011). Digital Origami: Modeling Planar Folding Surface. ACADIA Regional 2011: Parametricism: (SPC). Li, D. H., & Tsang, E. K. (2008). An analysis of daylighting performance foroffice buildings in Hong Kong. Building and Environment. McNeel, R. (2010). Grasshopper - Generative Modeling with Rhino. Retrieved June 24, 2014, from McNeel North America,Seattle, USA.: http://www.grasshopper3d.com/ Moloney, J. (2011). Designing Kinetics for Architectural Facades: State change. Routledge. Monks, M., Oh, B., & Dorsey, J. (2000). Audioptimization: goal-based acoustic design. Computer Graphics and Applications, IEEE. 20, pp. 76-90. IEEE. Motta, E. (1999). Reusable Components for Knowledge Modelling: Case Studies, in: Parametric Design Problem Solving. Amsterdam: IOS Press. Park, C.-S., Augenbroe, G., & Messadi, T. (2003). Daylighting optimization in smart facade systems. In Proceedings of the Eighth International IBPSA Conference. Peel, M. C., Finlayson, B. L., & McMahon, T. A. (2007). Updated world map of the KöppenGeiger climate classification. Hydrology and Earth System Sciences, 1633-1644. Poirazis, H. (2006). Double Skin Facades,A literature review. Rakha, T., & Nassar, k. (2011). Genetic algorithms for ceiling form optimization in response to daylight levels. Renewable Energy, 23482356. Ramos, G., & Ghisi, E. (2010). Analysis of daylight calculated using the EnergyPlus programme. Renewable and Sustainable Energy Reviews, 14(7), 1948-58. Reinhart, C. F. (2001). Daylight availability and manual lighting control in office buildings simulation studies and analysis of measurements. The university of Karlsruhe, Germany. Reinhart, C. F., & Wienold, J. (2011). The daylighting dashboard -A simulation-based design analysis for daylit spaces. Building and Environment. Reinhart, C. F., & Wienold, J. (2011). The daylighting dashboard -A simulation-based

design analysis for daylit spaces. Building and Environment,, (pp. 386-396). Reinhart, C. F., Mardaljevic, J., & Rogers, Z. (2006). Dynamic Daylight Performance Metrics for Sustainable Building Design. Leukos, 3, pp. 7-31. Reinhart, C., & Breton, P.-F. (2009). Experimental Validation of Autodesk® 3ds Max® Design 2009 and Daysim3.0. Leukos. Reinhart, C., & Walkenhorst, O. (2001). Dynamic RADIANCE-based daylight simulations for a full-scale test office with outer venetian blinds. Energy & Buildings. Reinhart, C., Lagios, K., & Niemasz, J. (2011). DIVA for Rhino Version 2.0. Retrieved June 10, 2014, from http://www.diva-for-rhino.com/ Schumacher, P. (2009, July). Parametricism - A New Global Style for Architecture and Urban Design. AD Architectural Design - Digital Cities. Sterner, C. (2014). Measuring Daylight: Dynamic Daylighting Metrics & What They Mean for Designers. Torres, Santiago L., S., & Yuzo. (2007). Facade design optimization for daylight with a simple genetic algorithm. Building Simulation. Turrin, M., Buelow, P. v., & Stouffs, R. (2011). Design explorations of performance driven geometry in architectural design using parametric modeling and genetic algorithms. Advanced Engineering Informatics, 25(4), 656–675. USGBC. (2013). LEED Reference Guide for Building Design and Construction v4. USGBC,. Washington DC 2013. Wagdy, A. (2013). New parametric workflow based on validated day-lighting simulation. 1st IBPSA Conference. Cairo, Egypt. Ward, G. (1994). The RADIANCE Lighting Simulation and Rendering System. the 21st Annual Conference on Computer, (p. Orlando.). Yoon, S.-H., Park, C.-S., & Augenbroe, G. (2011). On-line parameter estimation and optimal control strategy of a double-skin system. Building and Environment. Zemella, G., De March, D., Borrotti, M., & Poli, I. (2011). Optimised Design of Energy Efficient Building Façades via Evolutionary Neural Networks. Energy and Buildings, (pp. 3297-3302).

- 321 -