Built around well-tested Lodestar mechanics (among the best-known and best- ...
there are anomalies in the power supply, if a load movement error occurs or if ...
EXE LODESTAR 650C1 SAFETY THE BEST CHOICE. Our new multi-function chain hoist is purpose-designed for entertainment sector applications. Based on Lodestar mechanics with the addition of sophisticated EXE control electronics, this is the most complete and high-performance chain hoist available today, responding to the stringent criteria of BGV-C1 regulation.
CONCEPT / EXE-LODESTAR 650C1
EXE LODESTAR 650C1 CONCEPT
Built around well-tested Lodestar mechanics (among the best-known and best-respected on the market), EXE650C1 has been developed with safety as top priority: hence the choice of components which themselves offer intrinsic safety systems, and hence also the decision to develop the EXE dual core (dual processor) system.
COMPARISON OF FUNCTIONAL CHARACTERISTICS TECHNICAL DATA
MOTION
ACTION
EXE650C1 is available in two versions, Motion and Action. Both versions have the same characteristics and performance levels in terms of maximum load and safety.
Power Supply 400 Vac ±10% 3 fasi Frequency
50 Hz
Maximum power
0.75 Kw
Maximum current
2.4 A
Maximum lift load (C1 mode)
650 Kg.
Maximum overload limit (adjustable)
0-20%
Maximum lift load (C1 mode)
300-650 Kg.
Speed
4 m/minuto
Load weigth reading range
12
235
322
100-780 Kg.[*]
Weight reading possible during lifting
Sì
Sì
Weight reading possible during descent
No
Sì [*]
Weight reading possible when hoist is stopped
511
250-780 Kg.
No
Sì [*]
Minimum readable undercharge
250 Kg.
100 Kg [*].
Weight reading accuracy (360V -400V)
±30 Kg.
±5 Kg. [*]
Weight reading accuracy (400V -440V)
±40 Kg
±5 Kg. [*]
Display can be rotated 180°
Sì
Sì
Software end-stops
No
Sì [**]
Last 10 errors logged to memory
Sì
Sì
End-stops logged to memory
Sì
Sì
D8 mode temporarily activated by ket
Sì
Sì
D8 mode temporarily activated by button
Sì
Sì
Primary parameters can be set by keypad
Sì
Sì
All parameters can be set by DataLogger
Sì
Sì
* When fitted with load cell
Versions
** Setting possible when used with DataLogger
PRIMARY CHARACTERISTICS EXE650C1 is easy to install and use. It doesn’t require a dedicated controller, and is “Plug & Lift” - unpack it and it’s immediately operational.
>
Four limit-switch hardware to manage end-stops. Action models have two further software limiters. Temporary D8 mode operation to allow maintenance or emergency operation of the hoist.
13
MOTION / EXE-LODESTAR 650C1
EXE LODESTAR 650C1 MOTION
Motion is the version designed for use alone or in combination; it maintains all the priorities of safety and reliability, but, because it doesn’t have a position sensor, can not be used either with an external load cell or in synchronous mode.
Code
Description
Details
XH65C1M EXE-Lodestar “Motion” electric chain hoist
prefitted with upper hook & plug standard packaging - max 50 m
XH65C1MF EXE-Lodestar “Motion” electric chain hoist
prefitted with upper hook & plug version for flight case - max 50 m
XH65C1M18M* EXE-Lodestar “Motion” electric chain hoist 18 m
medium-sized chain bag (up to 25 m)
XH65C1M24M* EXE-Lodestar “Motion” electric chain hoist 24 m medium-sized chain bag (up to 25 m)
14
511
235
XH65C1M18L*
EXE-Lodestar “Motion” electric chain hoist 18 m large-sized chain bag (up to 40 m)
XH65C1M24L*
EXE-Lodestar “Motion” electric chain hoist 24 m large-sized chain bag (up to 40 m)
XHCBKM
Medium-sized chain bag (up to 25 m)
with snap hooks
XHCBKL
Large-sized chain bag (up to 40 m)
with snap hooks
XHCBKX
X-Large-sized chain bag (up to 72 m)
with snap hooks
CHCL00
EXE chain
(price per meter)
CH0LUH
Upper swivel Latchlok Hook
for EXE 650 C1
CH0FLLH
Upper swivel Latchlok Hook
for EXE 650 C1
XF6501
Flight case
for one EXE-Lodestar 650 C1 chain hoist
XDL12
EXE DataLogger - 12 channels
with battery charger
XHCB005
Bus cable for EXE-Lodestar 650 C1 chain hoist
5 m length
XHCB010
Bus cable for EXE-Lodestar 650 C1 chain hoist
10 m length
XHCB025
Bus cable for EXE-Lodestar 650 C1 chain hoist
25 m length
XHCB050
Bus cable for EXE-Lodestar 650 C1 chain hoist
50 m length
CHHLBK
Motor cover
black
CHHLG
Motor cover
silver
Es. XH65C1Mxx_ 322
xx = chain meters _ = M, L o X (size of the chain bag) * Height of lift (HOL) is the nominal length plus 1 meter
TECHNICAL DATA
EXE-Lodestar 650C1 MOTION
PRIMARY CHARACTERISTICS
Power Supply
400 Vac ±10% 3 fasi
Lifting and self-supporting functions
Frequency
50 Hz
Maximum power
0.75 Kw
Double Stromag brake
Maximum current
2.4 A
Maximum lift load (C1 mode)
650 Kg.
Maximum overload limit (adjustable)
0-20%
Electronic over- and underload control
Maximum load limit (adjustable)
300-650 Kg.
Temporary manual over- and underload protection bypass
Speed
4 m/minut
Can be linked to EXE series chain hoists and intelligent electronic devices (DataLogger)
Temporary C1 and D8 mode selection via operator panel Load reading during lifting (without load cell)
Simultaneous blocking of all linked motors in the event of a fault, even in a single motor
Automatic emergency stop happens when: Over- or undercharge detected Data bus command received Data line interrupted Internal fault detected Power line anomalies detected Internal temperature limit exceeded Current surge detected Preset run limits exceeded Emergency stop button pressed
Display data can be switched between the following: Chain hoist ID number Power supply tension Current Load weight Hoist internal temperature
15
ACTION / EXE-LODESTAR 650C1
EXE LODESTAR 650C1 ACTION
Action is the version designed to be fitted and used with an (optional) external load cell allowing for precise weight measurement as well as for synchronous mode operation (using DataLogger) with optimum performance and no safety sacrifices.
Code
16
511
235
Description
Details
XH65C1A EXE-Lodestar “Action” electric chain hoist
prefitted with upper hook & plug standard packaging - max 34 m
XH65C1AF EXE-Lodestar “Action” electric chain hoist
prefitted with upper hook & plug version for flight case - max 34 m
XH65C1A18M*
EXE-Lodestar “Action” electric chain hoist 18 m
medium-sized chain bag (up to 25 m)
XH65C1A24M*
EXE-Lodestar “Action” electric chain hoist 24 m
medium-sized chain bag (up to 25 m)
XH65C1A18L*
EXE-Lodestar “Action” electric chain hoist 18 m
large-sized chain bag (up to 40 m)
XH65C1A24L*
EXE-Lodestar “Action” electric chain hoist 24 m
large-sized chain bag (up to 40 m)
XHCBKM
Medium-sized chain bag (up to 25 m)
with snap hooks
XHCBKL
Large-sized chain bag (up to 40 m)
with snap hooks
XHCBKX
X-Large-sized chain bag (up to 72 m)
with snap hooks
CHCL00
EXE chain
(price per meter)
CH0LUH
Upper swivel Latchlok Hook
for EXE 650 C1
CH0FLLH
Upper swivel Latchlok Hook
for EXE 650 C1
XF6501
Flight case
for one EXE-Lodestar 650 C1 chain hoist
XDL12
EXE DataLogger - 12 channels
with battery charger
XHCB005
Bus cable for EXE-Lodestar 650 C1 chain hoist
5 m length
XHCB010
Bus cable for EXE-Lodestar 650 C1 chain hoist
10 m length
XHCB025
Bus cable for EXE-Lodestar 650 C1 chain hoist
25 m length
XHCB050
Bus cable for EXE-Lodestar 650 C1 chain hoist
50 m length
CHHLBK
Motor cover
black
CHHLG
Motor cover
silver
Es. XH65C1Axx_ 322
Automatic emergency stop happens when: Over- or undercharge detected Data bus command received Data line interrupted Internal fault detected Power line anomalies detected Internal temperature limit exceeded Current surge detected Preset run limits exceeded Emergency stop button pressed
Display data can be switched between the following: Chain hoist ID number Power supply tension Current Load weight Hoist internal temperature
xx = chain meters _ = M, L o X (size of the chain bag) * Height of lift (HOL) is the nominal length plus 1 meter
TECHNICAL DATA
EXE-Lodestar 650C1 ACTION
FUNCTIONAL CHARACTERISTICS OF THE ACTION MODEL
Power Supply
400 Vac ±10% 3 fasi
Lifting and self-supporting functions
Temporary manual over- and underload protection bypass
Frequency
50 Hz
Maximum power
0.75 Kw
Double Stromag brake
Controllo elettronico di sovraccarico e sottocarico
Maximum current
2.4 A
Temporary C1 and D8 mode selection via operator panel
Connection line for linking to intelligent electronic devices (DataLogger)
Maximum lift load (C1 mode)
650 Kg.
EXE dual core system controls safety functions
Maximum overload limit (adjustable)
0-20%
Load reading during lifting
Double connection line for linking to EXE series chain hoists, predisposed for synchronous operation (with external control unit)
Maximum load limit (adjustable)
300-650 Kg.
Electronic over- and underload control
Speed
4 m/minuto
Precise reading of load during lifting via external load cell
Simultaneous blocking of all linked motors in the event of a fault, even in a single motor
Precise reading of load also during lowering via external load cell
Chain position reading
17
DATALOGGER / EXE-LODESTAR 650C1
DATALOGGER
EXE DataLogger C1 is a supervision and control unit for the EXE Lodestar family of chain hoists, integrating their safety functions in complete accordance with BGV-C1 regulations. It is especially suited to applications requiring the use of several chain hoists to move a single load.
Code
FUNCTIONAL CHARACTERISTICS OF DATALOGGER
Description
With its simple, yet robust and functional design, DataLogger simplifies the management and use of chain hoists with diagnostic functions which allow monitoring (and often modification) of all the hoist’s working parameters, even when the hoist is installed in hard-to-reach places.
XDL12
XHCB005
Bus cable for EXE-Lodestar 650 C1
L= 5 m
During normal operation of the chain hoist, EXE DLC1 visualizes and stores to memory the dynamic data from the hoist, allowing the operator to keep a precise and constant check of the hoist’s working condition.
XHCB010
Bus cable for EXE-Lodestar 650 C1
L= 10 m
XHCB025
Bus cable for EXE-Lodestar 650 C1
L= 25 m
XHCB050
Bus cable for EXE-Lodestar 650 C1
L= 50 m
EXE DataLogger - 12 channels - with battery charger
XDL12-BC EXE DataLogger battery charger
The EXE DLC1 can be connected to a single chain hoist or to the line linking several hoists together. When the EXE DLC1 is connected to a group of (up to 12) chain hoists operating on a single load, new control and monitoring functions become available. All these functions follow BGV-C1 safety criteria. The most significant of these functions are load weighing and synchronous movement. Load weighing: by using load cells, each hoist can measure the load applied both in dynamic conditions (i.e. during load lifting) and when the load is static. By presetting the EXE DLC1 with the hoists one wishes to consider, one can view the weight applied to each individual hoist during operation, as well as checking the total load, whether dynamic or static, across all hoists.
18
19
Synchornous movement: when using EXE Lodestar Action chain hoists, the DataLogger receives information about the position of each individual hoist during movements. It also checks the data received in order to keep all hoists perfectly aligned during combined movements. In order to guarantee maximum safety during operations while also ensuring that emergency interventions and maintenance can be carried out, access to EXE DLC1 functions is password-protected for various use levels. This also helps avoid accidental or incorrect modification of critical parameters during normal operation. The large screen, backlit (and checmical-resistant) keypad and the long internal battery life make the EXE DLC1 a professional tool ideally adapted to all conditions of use.
TECHNICAL DATA
DATALOGGER
Power Supply
Internal: NiMh batteries External: power supply / battery charger code XDL12BC
Screen
4” graphic screen (128x128 backlit)
Keypad
Membrane with audible click Numeric keypad with 12 buttons for quick access to hoist information/data
Connectors
Data in-out line AC power supply / battery charger line
1
Global parameters set-up
2
Tool ignition
3
Display of 12 chain hoists
4
Linked chain hoists data
5
Total weighing of all chain hoists
1
2
3
4
5
ACCESSORIES / EXE-LODESTAR 650C1
ACCESSORIES
Litec has chosen some high-quality and performing products that complete the EXE-Lodestar chain hoists line. The chosen accessories, such as the Load cell, latchlok hooks, hoist covers and flight case, allow professionals to work safely and comfortably.
LATCHLOK HOOKS CM Latchlok hooks combine innovative design and solid alloy steel. I-beam construction offers more reliable performance than any other hook on the market. One-hand operation and recessed push-button thumb release for smooth and dependable opening. Hook remains locked until released by the operator, even if chain goes slack. Sturdy forged heat treated I-beam construction for strong yet lightweight hooks.
TECHNICAL DATA
CHOLUH _ CHOFLLH
CH0LUH
Upper swivel Latchlok Hook for EXE 650 C1
CH0FLLH
Lower swivel Latchlok Hook for EXE 650 C1
MOTOR COVER
20
CHHLBK _ CHHLG Litec hoist covers for Lodestar F-L-RR models are made of 600 denier woven polyester with two coats of resin, and protect hoists from the elements.
TECHNICAL DATA
CHHLBK _ CHHLG
CHHLBK
Motor cover / Black
CHHLG
Motor cover / Silver
- Made of waterproof polyester with two coats of resin - Black or grey 600 x 600 denier woven fabric - Double seam with Cucirini high resistance thread - Polyester wear-resistant edge binding - Front strap opening
FLIGHT CASE XHF6501
A flight case for EXE650-C1 chain hoists is available.
TECHNICAL DATA
FLIGHT CASE XHF6501
Description
Flight case for EXE-Lodestar 650 kg
Weight
37 kg
Dimensions
740x580x570 cm on wheels
LOAD CELL TECHNICAL DATA Load cell coupled with EXE 650C1 chain hoists and compatible with BGVC1 standard. Supplied with suitable eyebolts. It has 10:1 safety factor in applications with EXE 650C1 chain hoist. It is provided with the link connector with EXE650C1 chain hoist and 1.5 m shielded cable. Available soon (first quarter 2010).
Dimensions
82 x 78 x 30 mm
Connection
with Litec eye-bolts M20 x 1.5 x 20
Operating temperatur
-20/+70 °C
Made in
stainless steel
Protection class
IP68
- Made of birch plywood covered with scratchresistant laminate - Phenolic gluing to ensure excellent resistance to sudden changes in temperature - Internal dividers, without sharp edges, shaped to house the hoist - Stackable - 4 guiding wheels (2 with brakes)
21