PAPER CRAFT

5 downloads 6535 Views 582KB Size Report
Thank you for downloading the "VMAX" paper craft model. By simply fol- .... F-7 (F -14). F-6 (F-13). F-15 (F-16). F-17 (F-18). F-19 (F-20). F-5 (F-12). * Make two of ...
PAPER CRAFT Assembly Instructions

Thank you for downloading the "VMAX" paper craft model. By simply following this manual while referring to the names and numbers shown on the parts sheets, you can assemble an authentic-looking replica of the VMAX.

Assembly instructions: Fifteen A4-sized sheets. Paper craft: Sixteen A4-sized sheets with 174 parts in all

These instructions apply only to the "VMAX". Other paper craft model instructions can be downloaded separately. The parts are easier to work with when printed on strong, thick paper.

Note

Basic working method and markings

TO BEGIN Tools and materials needed

Solid lines

-Ruler -Scissors - Blade cutter or "Exacto-knife" - Awl or other pointed tool (for making a folding crease) - Felt pen - Pin set - Glue - Hand towel ( for cleaning your fingers) - Dictionary or other heavy book ( to press the papers flat)

Fold along these lines. The printed surface should be on the outside of the folded shape.

Broken lines

Item of Caution *Take care when using sharp or pointed objects or when using bladed cutting tools. Place a heavy sheet of paper under the paper you want to cut. *Use glue and other adhesives only in well-ventilated areas. *When printing, use a slightly reduced font size as there are many differences in dimensions depending on the type of printer used.

Fold along these lines. The printed surface should be on the inside of the folded shape.

Dotted line Cut along these lines

HOW TO ASSEMBLE Do not fold or cut the parts marked .

*Follow the working method and markings carefully. *Cut carefully along the outter line with a cutting blade, Exacto-knife or scissors.

One - point Advice

Cut out parts marked with an asterisk (*).

*Cut carefully with a cutting blade, Exacto-knife or scissors. *For folding parts, first use an awl or other pointed tool to make a light crease along the dotted or solid line. This will make the folds straight. Avoid making strong creases, as this will cause the paper to tear.

Red dots are the reference positions for gluing surfaces.

*As an adhesive, white, wood glue is recommended. Avoid over application as this will cause the paper to wrinkle. *Before beginning assembly, test adhesive amounts on extra paper. *Occasionally, white spots will be apparent on folds and cuts. Use a marker or pencil to fill-in these spots. It is recommended that this be done after each stage of assembly because coloring becomes more difficult once parts are assembled.

-2-

1

Assembling the Body

First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Body Sheet A, 1 part in total

Indication of Working Methods

Fold or Curve

Fold each relevant part according to the assembly symbols.

A-1

Reference photo

-3-

Glue

2

Assembling the Steering Column

First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Fold or Curve

Steering column

Fold each relevant part according to the assembly symbols.

Sheet B, 24 parts in total

Please use the

dots on each component as reference when gluing surfaces.

B-3

B-4 B-9

B-5 B-6 B-13

B-1 B-12 B-10

B-7

B-14 B-11

B-2

B-24

B-8

Reference photo B-15

B-23 B-20 B-16 B-17

B-18

B-22

Glue

B-19 B-21 Apply glue on the area indicated in the illustration.

-4-

3

Assembling the Top Cover and Intake

First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Glue

Fold or Curve

Top cover

Fold each relevant part according to the assembly symbols.

Sheet C, 2 parts in total

Please use the

dots on each component as reference when gluing surfaces.

C-1 C-2

C-2

Reference photo

Fold and glue the parts making sure both tabs (illustrated by dotted-lines) are neatly tucked in.

Intake Sheet D, 2 parts in total

D-2

Fold each relevant part according to the assembly symbols.

D-1

-5-

Reference photo

4

Assembling the Engine

First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Glue

Fold or Curve

Engine

Fold each relevant part according to the assembly symbols.

Sheet E, 47 parts in total

Please use the

dots on each component as reference when gluing surfaces. E-29 (E-31) E-28 (E-30)

E-33 (E-35)

E-44 (E-45)

E-32 (E-34) E-8 (E-14) E-12 (E-10)

E-36 (E-38)

E-11 (E-9) E-41 (E-43) E-7 (E-13) E-17 (E-18)

E-24 (E-27) E-37 (E-39) E-1 (E-2) E-21 (E-22) E-15 (E-16)

E-40 (E-42)

E-26 (E-25) E-46 (E-47)

E-20 (E-19)

E-5 (E-6) E-3 (E-4)

E-23 * Only the left part is available.

Reference photo Left

* Make two of each part. The diagram shows how the left part of the engine looks. The numbers within parentheses indicate parts for the right part of the engine.

Right

-6-

5

Assembling the Side Covers

First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Fold or Curve

Side covers

Fold each relevant part according to the assembly symbols.

Sheet F, 20 parts in total

Please use the

Glue

dots on each component as reference when gluing surfaces.

* Make two of each part. The diagram shows how the left frame cover looks. The numbers within the parentheses indicate parts for the right frame cover. F-5 (F-12) F-1 (F-8) F-4 (F-11) F-19 (F-20)

F-2 (F-9) F-7 (F-14)

F-17 (F-18)

F-3 (F-10) F-6 (F-13)

F-15 (F-16)

Reference photo

Right

Left

-7-

6 Assembling the Exhaust First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Glue

Fold or Curve

Exhaust

Fold each relevant part according to the assembly symbols.

Sheet G, 23 parts in total

Please use the

dots on each component as reference when gluing surfaces.

in the diagram indicate where parts are to be glued later. Please do not glue parts at this stage. G-14 G-15 To the right side of the engine.

G-22

G-16

G-20 G-17 G-4

G-18

G-21

G-1

G-2 G-5 G-19 G-3 G-23

G-8 G-13

G-7 G-6

When gluing each part, make sure the angle is correct, referring to the photo below.

G-12

To the left side of the engine.

G-11 G-9

G-10

Reference photo Exhaust A

Exhaust B

Partition of exhaust pipes - Exhaust A (Right) G-1 to G-4 - Exhaust A (Left) G-5 to G-8 - Exhaust B (Right) G-14 to G-18 - Exhaust B (Left) G-9 to G-13 - Exhaust pipe C G-19 to G-23

Exhaust C

-8-

7 Assembling the Radiator and Rear Suspensions First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Fold or Curve

Radiator

Fold each relevant part according to the assembly symbols.

Sheet H, 3 parts in total

Please use the

Glue

dots on each component as reference when gluing surfaces.

H-3 H-2

Reference photo H-1

Rear suspensions

Fold each relevant part according to the assembly symbols.

Sheet I, 8 parts in total

Please use the dots on each component as reference when gluing surfaces.

* Make two of the rear suspensions. They should be identical. The numbers within the parentheses indicate the parts for the second suspension.

I-3 (I-4)

Reference photo I-5 (I-6)

I-1 (I-2)

I-7 (I-8) Apply glue on the area indicated in the illustration.

-9-

8 Assembling the Rear Fender and Seat First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Glue

Fold or Curve

Rear fender

Fold each relevant part according to the assembly symbols.

Sheet J, 3 parts in total

Please use the

dots on each component as reference when gluing surfaces.

J-2

Reference photo

J-1

J-3

Seat

Fold each relevant part according to the assembly symbols.

Sheet K, 9 parts in total

Please use the

dots on each component as reference when gluing surfaces. K-1

K-5 K-3

K-2 K-4 K-6

K-8

K-9

K-7

- 10 -

Reference photo

9 Assembling the Front Tire First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Fold or Curve

Front tire

Fold each relevant part according to the assembly symbols.

Sheet L, 13 parts in total

Please use the

dots on each component as reference when gluing surfaces.

L-2 L-4

Glue

L-13 L-7 L-10 L-11

L-5

L-9 L-8 L-6 L-12 L-3 L-1

Reference photo

- 11 -

10 Assembling the Rear Tire First, assemble each component by following the working method and markings. Then, refer to the illustration and photos below to glue the parts together.

Indication of Working Methods

Fold or Curve

Rear tire

Fold each relevant part according to the assembly symbols.

Sheet M, 19 parts in total

Please use the

dots on each component as reference when gluing surfaces.

Reference photo

*Glue the completed rear arm to the assembled rear tire.

[Rear tire] M-8 M-9 M-6 M-11 M-3 M-4

M-12

[Rear arm]

M-18

To the rear tire.

Glue

M-17 M-2 M-1 M-10

M-16 M-19

M-1

M-5 To the rear arm.

M-15

M-13

- 12 -

11 Finish Please use the

dots on each component as reference when gluing surfaces. Side cover (Right) Top cover

Assembly Instructions

Side cover (Left)

Seat

Rear fender

Intake (Right)

glue the assembled parts in numerical order through .

Rear suspensions

Engine (Right) Glue the right and left parts of the engine to the body. Glue the right and left parts of the intake to the body. To the Right intake.

To the right frame cover.

Glue the rear tire to the body. Glue the right and left side covers to the body. Glue the rear fender to the right and left frame covers. Glue the right and left rear suspensions to the rear tire and the right and left side covers. Glue exhaust C to the rear tire. Insert the right and left exhaust B into the engine. After inserting the right and left exhaust A into the engine, insert exhaust pipes A and B into exhaust C. Glue the seat to the body.

Body Rear tire

Glue the fuel top cover to the body and seat.

Engine (Left)

Glue the radiator to the body. Glue the front tire to the steering column. Glue the part completed in

Intake (Left)

to the body.

To the Right engine.

Steering column

Front tire

Exhaust C

Exhaust B

Radiator Exhaust A

- 13 -

12 Assembled Model and the List of Parts Please refer to the photo below when attaching each component.

FRONT

RIGHT Engine (Right)

Side cover (Right) F-8 F-9 F-1 0 F-1 1 F-1 2

F-1 3 F-1 4 F-1 6 F-1 8 F-2 0

Top cover

Intake (Right)

C-1 C-2

D-2

E-2 E-4 E-6 E-9 E-1 0 E-1 3 E-1 4

Body A-1

E-1 6 E-1 8 E-1 9 E-2 2 E-2 5 E-2 7 E-3 0

E-3 1 E-4 5 E-3 4 E-4 7 E-3 5 E-3 8 E-3 9 E-4 2 E-4 3

Steering column

Rear suspension (Right) I-2 I-6 I-4 I-8

Exhaust

Front tire

G-1 G-2 G-3 G-4 G-5 G-6

L-1 L-2 L-3 L-4 L-5

G-7 G-8 G-9 G-1 0 G-1 1 G-1 2

G-1 3 G-1 4 G-1 5 G-1 6 G-1 7 G-1 8

G-1 9 G-2 0 G-2 1 G-2 2 G-2 3

- 14 -

L-6 L-1 1 L-7 L-1 2 L-8 L-1 3 L-9 L-1 0

B-1 B-2 B-3 B-4 B-5 B-6 B-7

B-8 B-9 B-1 0 B-1 1 B-1 2 B-1 3 B-1 4

B-1 5 B-2 2 B-1 6 B-2 3 B-1 7 B-2 4 B-1 8 B-1 9 B-2 0 B-2 1

12 Assembled Model and the List of Parts Please refer to the photo below when attaching each component.

REAR

LEFT Seat K-1 K-2 K-3 K-4 K-5

Intake (Left) D-1

Rear fender K-6 K-7 K-8 K-9

J-1 J-2 J-3

Radiator H-1 H-2 H-3

Rear suspension (Left) I-1 I-3 I-5 I-7

Engine (Left) E-1 E-3 E-5 E-7 E-8 E-1 1

E-1 2 E-1 5 E-1 7 E-2 0 E-2 1 E-2 3

E-2 4 E-2 6 E-2 8 E-2 9 E-3 2 E-3 3

E-3 6 E-3 7 E-4 0 E-4 1 E-4 4 E-4 6

Side cover (Left)

Rear tire

F-1 F-4 F-7 F-1 9 F-2 F-5 F-1 5 F-3 F-6 F-1 7

M-1 M-2 M-3 M-4 M-5

- 15 -

M-6 M-7 M-8 M-9 M-1 0

M-1 1 M-1 2 M-1 3 M-1 4 M-1 5

M-1 6 M-1 7 M-1 8 M-1 9