Saturn Cutoff LED Install Instructions

Saturn Cutoff LED and Saturn 2 Cutoff LED Installation Instructions: Post Top Tools Required (not included) 4mm Allen Wrench #10 Spanner Head Driver SAC2L

(shown for reference)

1. Run Feed Cord from Luminaire into top of Pole (fixture does not need to be opened; it ships ready to install). 2. Place Luminaire onto Pole. 3. A im the fixture as intended. Always position Street Side Label at street side (see label next to glass). 4. Level and secure into place by tightening (2) Set Screws with Allen Wrench. 5. L oosen Handhole Screws and remove Handhole Cover. Connect Feed Cord from Luminaire to Line Voltage Feed (by others). See wiring on page 4 for proper installation. Be sure not to pinch wires during installation. 6. Replace Handhole Cover and test fixture.

SACL Luminaire

10 5/16" [262mm] Driver Depth

4 1/8" [105mm] Fitter Depth, Ref

#10 Spanner Head Driver

Set Screws (4mm Allen Wrench)

Pole

Feed Cord (from Luminaire)

Handhole Cover

3 1/8" [79mm] Minimum Pole I.D. Pole

For details and spec sheet for Saturn Cutoff LED, scan here.

CAUTION

DANGER

LED Radiation.

Hazardous voltage.

Do not operate while LEDs are exposed.

Only work on de-engergized equipment. Disconnect power before wiring fixture.

Do NOT stare into Beam. Can cause eye damage.

Contact will cause electric shock or burn.

Selux Corporation © 2014, T 845-834-1400, 800-735-8927, F 845-834-1401, www.selux.us Please Note: Disconnect electricity to fixture before working. To be performed by trained personnel only. It is the responsibility of the installer to ensure all electrical, mechanical, and thermal compatibility of the installation site and luminaires prior to installation. Please observe all relevant building codes and regulations. Keep these instructions after unpacking fixture. For outdoor use only. For detailed spec sheets and more information on this and our full range of products, please visit our website at selux.us. Warranty information: http://www.selux.us/en/resources/terms-and-warranty.html

NOTICE

Do not touch LED

May damage device

Observe precautions for handling electrostatic sensitive devices.

Page 1 of 5 (Rev. 07/14) SACL_INST_v3.3

Saturn Cutoff LED and Saturn 2 Cutoff LED Gear Tray Maintenance Tools Required (not included) #10 Spanner Head Driver Phillips Head Screwdriver

1. Disconnect Power. 2. Loosen Handhole screws and remove Handhole Cover (not shown). Disconnect luminaire Feed Cord from Line Voltage Feed (not shown). 3. T wist lower cover counter-clockwise to remove cover. 4. Loosen (2) M6 pan head screws (do not remove screws). 5. T urn gear tray counter-clockwise and lift Gear Tray Assembly out of pole, just enough to expose terminal blocks. 6. Disconnect white, black and green wires coming from side tubes. Remove Gear Tray Assembly from pole along with the attached Feed Cord from Luminaire. 7. Run Feed Cord from the new Gear Tray Assembly into Pole. 8. P lace New Gear Tray Assembly partly into pole exposing the terminal blocks. Reconnect wires from side tubes according to wiring shown on page. 9. Reinstall Gear Tray Assembly. Tighten (2) M6 pan head screws. Reinstall lower cover. 10. C onnect the new Feed Cord from Luminaire to Line Voltage Feed. 11. Replace Handhole Cover and test Luminaire.

Connect WHITE Wire from Side Tubes with RED Wire from Gear Tray Assembly Connect BLACK Wire from Side Tubes with BLACK Wire from Gear Tray Assembly Top Terminal Block RED BLACK

WHITE BLACK

Wires going to the rest of the Gear Tray Assembly

GREEN

GREEN

WHITE BLACK GREEN

Wires from Side Tube

Bottom Terminal Block Connect GREEN Wire from Side Tubes with GREEN Wire from Gear Tray Assembly

3 5 4

(Phillips Head) Top Terminal Block Bottom Terminal Block

6


CAUTION

Wires from Side Table

DANGER

LED Radiation.

Hazardous voltage.






NOTICE

Do not touch LED

May damage device



Saturn Cutoff LED and Saturn 2 Cutoff LED Light Engine Maintenance Tools Required (not included) #14 Spanner Head Driver Bit Phillips Head Screwdriver

1. Disconnect power. 2. Loosen tamper-resistant screws using spanner head screwdriver. 3. L ift cap off fixture and disconnect red, black, and green wire connections. 4. Loosen (9) MS pan head screws holding light engine to cap (do not remove screws). 5. Remove light engine assembly by using keyhole design. 6. Replace with new light engine, tighten screws and connect red, black and green wires according to wiring shown on page. Ensure gasket is clean and damage-free. 7. Replace top cap making sure not to pinch wires and tighten tamper-resistant screws. 8. Reconnect to power and test luminaire.

Wire connection detail for #3 and #6 Wire Connectors

WHITE

RED

BLACK

BLACK

GREEN

GREEN


Cap with Attached Light Engine

3

2

4

5 For details and spec sheet for Saturn Cutoff LED, scan here.

CAUTION

DANGER

LED Radiation.

Hazardous voltage.






NOTICE

Do not touch LED

May damage device



Saturn Cutoff LED and Saturn 2 Cutoff LED Wiring US: Post Top

HI-LO SWITCHING OPTION (HLxx) WIRING

Hi-Lo Switching Option (HL) Wiring LG3700 and LG3105, 120V, 240V, 277V. When red is energized, light output will be at “Lo” level.

Standard Single Wiring & Dynadim (DMY)

120/240/277V. WHEN RED IS ENERGIZED, LIGHT OUTPUT WILL BE AT "LO" LEVEL. SPECIFY THE "LO" OUTPUT LEVEL BY SELECTING FROM THE TABLE BELOW. FOR OTHER PERCENTAGE OUTPUT LEVELS, CONSULT FACTORY.

SURGE PROTECTOR

SURGE PROTECTOR

BLACK

L1 FROM LINE CORD

L1 N

WHITE

N

GREEN

LIGHT ENGINE

0-10V DIMMING WIRING FOR 120-270V

WHITE GREEN

FROM LINE CORD

L2

0-10V Dimming Option (DM) Wiring LG3700 and LG3105, 120-277V.

BLACK

347/480 V

RED

STANDARD WIRING FOR 347/480V

SURGE PROTECTOR

SURGE PROTECTOR

N

BLACK

L1 FROM LINE CORD

WHITE GREEN

FROM LINE CORD Dim (+)

RED

Dim (-)

ORANGE

RELAY

STANDARD WIRING FOR 347/4800V WITH NO ADDITIONAL OPTIONS

100% LIGHT OUTPUT AT 10V, DOWN TO 10% LIGHT OUTPUT AT 0V.

L1

LIGHT ENGINE

N

LIGHT ENGINE

CAUTION

AUTO TRANSFORMER

BLACK WHITE GREEN

LIGHT ENGINE

DANGER

LED Radiation.

Hazardous voltage.






NOTICE

Do not touch LED

May damage device



Saturn Cutoff LED and Saturn 2 Cutoff LED Shade Replacement Tools Required (not included) #14 Spanner Head Driver Bit Phillips Head Screwdriver 13mm Wrench

Wire connection detail for #3 and #7 Wire Connectors

WHITE

RED

BLACK

BLACK

GREEN

GREEN


1. Disconnect power. 2. Loosen tamper-resistant screws using spanner head screwdriver. 3. L ift cap off fixture and disconnect red, black, and green wire connections. 4. Remove (2) hex nuts and flat washers, and (2) pan head screws holding shade in place. 5. Remove and replace shade. 6. Reinstall (2) hex nuts and flat washers, and (2) pan head screws to secure the shade. 7. Reconnect red, black, and green wires according to wiring shown on page. Ensure gasket is clean and damage-free. 8. R eplace top cap making sure not to pinch wires and tighten tamper-resistant screws. 9. Reconnect to power and test luminaire.

Cap with Attached Light Engine

3

4

2 5


CAUTION

DANGER

LED Radiation.

Hazardous voltage.






NOTICE

Do not touch LED

May damage device

